Springfield Hot Water HelpNo-hot-water help for the 417 (417) 929-5559Call
Springfield, MO & the 417

No hot water in the house in Springfield?

It's usually one of four things: a pilot or burner that went out, a tripped breaker or safety switch, a failed heating element, or a setting. Run the safe 10-minute checks below. Still cold? Talk to a local plumber.

Springfield Hot Water Help is a free info site, not a plumbing company. This number connects you to an independent local plumber who sets their own pricing and schedule.

  • Gas, electric & tankless checks
  • Safety-first advice
  • Updated November 2026
Hand held under a running bathroom faucet on a cold morning, with no steam rising from the water

The short answer

No hot water anywhere in the house means the water heater has stopped heating. On a gas heater the pilot or burner is usually out. On an electric heater a breaker or safety switch has tripped, or an element has burned out. On a tankless unit, the display will usually show an error code.

Some of these are a two-minute fix you can do yourself, and the checklist below separates what's safe to check from what needs a plumber. If only one faucet or shower is cold, the heater is probably fine and the problem is that fixture.

Smell gas or a CO alarm going off? Stop troubleshooting. Get everyone outside right away, don't flip switches or use a flame, then call 911 or your gas utility from outside. If you're on propane, call your propane supplier too.

10-minute checklist before you call

Work down the list in order. Don't remove any panels or covers.

  1. Check more than one faucet. Run hot water at the kitchen sink and a bathroom. Cold everywhere points to the heater. Cold at one fixture points to that faucet or shower valve.
  2. Find out what kind of heater you have. A gas tank has a vent pipe on top and a gas line to a control knob near the bottom. An electric tank has neither. A tankless unit is a box on the wall.
  3. Electric: check the breaker. Find the breaker labeled water heater. If it's tripped, switch it fully off, then on, once. If it trips again, leave it off and call.
  4. Gas: check the supply. The handle on the gas line should be parallel to the pipe. See whether your furnace or stove still works. On propane, check the tank gauge.
  5. Gas: look for the pilot or status light. Newer heaters have a small blinking light on the gas control; write down the blink pattern. If the pilot is out and you don't smell gas, relight it once using the instructions printed on the tank.
  6. Check the temperature dial. It should be around 120°F, not on VACATION, PILOT or LOW.
  7. Tankless: read the display. Write down any error code. Make sure the unit has power and that the intake and exhaust pipes outside are clear of ice, leaves and nests.
  8. Look at the floor around the heater. Water at the base means a leak. Close the cold-water valve above the heater, turn the heater off, and call.

Went through all eight and it's still cold after an hour or two? That's a plumber problem. Call and tell them what you found.

Call (417) 929-5559
Gas control knob and status light near the bottom of a tank water heater
The gas control near the bottom of the tank holds the temperature dial and, on newer heaters, a status light that blinks a fault code.

How long should it take to heat back up?

Once power or gas is back, a gas tank usually needs roughly 30 to 60 minutes and an electric tank one to two hours. Still cold after that means a part has failed.

What your water heater is telling you

The symptom narrows the cause down fast, and it's what a plumber will ask you on the phone.

What you noticeLikely causeWho fixes it
Gas heater, no hot water, pilot or status light offPilot out, failed thermocouple or igniter, gas supply offRelight once Plumber if it won't stay lit
Electric heater, no hot water at allTripped breaker or high-limit switch, failed upper element or thermostatCheck breaker Plumber
Lukewarm, or hot water runs out fastFailed lower element, heavy sediment, broken dip tube, dial set lowCheck dial Plumber
Hot at some faucets, cold at oneFaucet cartridge or shower mixing valve, not the heaterPlumber, for that fixture
Tankless unit shows an error codeIgnition fault, blocked vent, scale buildup, or freeze-upClear vents Plumber
Rumbling or popping from the tankSediment built up on the bottom of the tankPlumber
Rusty hot water or a rotten-egg smellWorn anode rod or a corroding tankPlumber
Water pooling at the base of the tankLeaking tank, fitting or relief valveShut off water, call now
Gas smell or CO alarmPossible gas leak or venting problemGet out, call 911

7 reasons you have no hot water

1. The pilot or burner went out

A draft, a worn thermocouple or a failed igniter shuts the burner down, and the tank slowly goes cold. A pilot that won't stay lit after relighting needs a part replaced.

2. A breaker or safety switch tripped

Electric heaters have a breaker in the panel and a high-limit switch on the tank that cuts power if the water overheats. The switch sits behind a cover with 240-volt wiring, so leave it to a plumber. If either keeps tripping, a thermostat or element is failing.

3. A heating element burned out

Electric tanks have two elements. When the upper one fails you get no hot water. When the lower one fails you get a short burst of hot water that runs out fast.

4. The gas or propane is off

A closed gas valve, an interrupted gas service or an empty propane tank leaves the heater with nothing to burn. If your furnace and stove are out too, this is the likely cause.

5. Sediment or a broken dip tube

Minerals settle on the bottom of the tank and insulate the water from the burner or element. A broken dip tube mixes cold water in at the top. Either one gives you lukewarm water and less of it.

6. Winter is slowing the heater down

The water coming into your house is much colder in January than in July, so a tank takes longer to recover and a tankless unit delivers cooler water at high flow. A heater that was barely keeping up in fall can fall short in a cold snap.

7. The tank is at the end of its life

Tank water heaters often last around 8 to 12 years. Rusty water, rumbling, and moisture at the base on an older tank usually mean replacement, not repair. The age is on the rating label.

Quick test: heater or faucet?

Run hot water at the tap closest to the heater for two minutes. If it gets hot there but not at a far bathroom, the heater is working and the problem is in the plumbing or that fixture.

When to stop and call a plumber

Call if any of these are true after the checklist:

  • The pilot won't light, or goes out again after relighting
  • The breaker trips a second time
  • The water is still cold one to two hours after power or gas came back
  • There's water at the base of the tank, or the relief valve is dripping or discharging
  • The tankless unit shows an error code that returns after you clear the vents
  • The tank is over 10 years old and the hot water is rusty or the tank rumbles

Never cap or plug a relief valve that's releasing water. It's there to keep the tank from over-pressurizing.

What to tell the plumber

Gas, electric or tankless; the tank size and age from the rating label; whether the water is cold, lukewarm or runs out fast; any blink pattern or error code; and whether there's a leak. That helps them show up with the right parts.

Still no hot water?

Talk to a local plumber serving Springfield and the 417.

Call (417) 929-5559

Areas served

Calls are connected to a plumber serving homes in and around:

  • Springfield
  • Nixa
  • Ozark
  • Republic
  • Battlefield
  • Rogersville
  • Strafford
  • Willard

Who runs this site

Springfield Hot Water Help is a locally run information site. We are not a plumbing company and we don't do repairs. We publish safety-first troubleshooting help and connect callers to an independent local plumber.

No hot water: common questions

Why is there no hot water in my house?

On a gas water heater, the pilot or burner has usually gone out or the gas supply is off. On an electric one, a breaker or the high-limit switch has tripped, or a heating element has failed. On a tankless unit, look for an error code. Check power, gas and the temperature dial first.

How long does a water heater take to heat back up?

After power or gas is restored, a gas tank usually needs roughly 30 to 60 minutes to reheat and an electric tank one to two hours. If the water is still cold after that, a part has failed and the heater needs a plumber.

Why does my hot water run out so fast?

On an electric heater the lower element has often failed, so only the top of the tank gets hot. Heavy sediment, a broken dip tube or a thermostat set too low can do the same on any tank. In winter, colder incoming water also makes every tank recover more slowly.

Is it safe to relight a water heater pilot light myself?

Yes, if you do not smell gas and you follow the lighting instructions printed on the tank. If you smell gas, leave and call 911 or your gas utility. If the pilot will not light or will not stay lit after one or two tries, stop and call a plumber.

Why is my tankless water heater not working in cold weather?

A hard freeze can ice up the water lines or the condensate drain, or block the intake and exhaust. A power outage also switches off the unit's built-in freeze protection. Very cold incoming water can drop the output temperature at high flow. Note any error code on the display.

My water heater is leaking. What should I do?

Close the cold-water valve on the pipe above the heater, then turn the heater off: the breaker for electric, the gas control knob to OFF for gas. Keep clear of hot water and call a plumber. A leak from the tank itself usually means replacement; leaks at fittings and valves can often be repaired.

Call (417) 929-5559